- #ATT UVERSE MAIL SETTINGS HOW TO#
- #ATT UVERSE MAIL SETTINGS SOFTWARE#
- #ATT UVERSE MAIL SETTINGS PASSWORD#
#ATT UVERSE MAIL SETTINGS PASSWORD#
If the password was correct you will be brought to a page that will say Configuration Successful.Next you will be asked for the password for your AT&T U-verse router, this is the one we gathered in step 2.If you are following this example you can use the values defined in the screen shot below EXACTLY as they are displayed. Map to Host Port: This is the port the camera runs on.Port (or Range): These are the external (or outside) ports we want to forward.
Open a web browser and enter this will bring you to the routers Home Page.On the AT&T U-verse router there is a sticker (usually silver in color) that has the “System Password” or “Device ID” make a note of that password. There is a password that we will need to complete the setup. Now that we know the IP address of the camera will never change we can configure the ATT U-verse router.If you are setting up a second or third camera you can simply use the next IP address in succession (192.168.1.21, 92.168.1.22, 192.168.1.23 etc…) Primary DNS: This will also be the address of your AT&T U-verse router ( 192.168.1.254)Īs an example if your AT&T router has not been customized you can enter in the values shown below EXACTLY as you see them.If the router is in its default AT&T setup the address will be 192.168.1.254.Default Gateway: This is the IP address of your AT&T U-verse router.The range is as follows: 192.168.1.20 – 192.168.1.40(the 192.168.1 portion will always remain the same simply use the last number of your choice. On the AT&T U-verse router in its default configuration (which 99% are) a certain range of IP addresses can be used.IP Address: This will is the address you will assign to the camera.There are 4 values on the TCP/IP setup page below that we need to enter. The address of your camera needs to stay the same for this process so we are going to change this dynamic IP address to a static (or fixed) IP address. When you setup your WiFi Baby camera using the 10 Step guide your camera was assigned a dynamic (or changing) IP address.
#ATT UVERSE MAIL SETTINGS HOW TO#
In this guide we will demonstrate how to place a rule in your router that will allow your access to the camera through that firewall. The AT&T U-verse routers are in addition a firewall, so they will block all attempts to access your camera from outside your home network. There are some additional steps needed to allow access to your camera from outside you home WiFi Network. Before starting the steps in this guide please follow our 10 Step Quick Start Guide for the basic setup of your WiFi Baby.ĪT&T U-verse 2Wire routers are not UPnP “Universal Plug and Play” capable devices. Make sure that the outbox is empty before testing, and choose a new subject for your test message.This guide will show AT&T U-verse customers how to set up access to your WiFi Baby camera from OUTSIDE of your home WiFi network. Having made these changes, close down WLMail and wait a few minutes before relaunching and testing both send and receive. On the Advanced tab, deselect both boxes for This server requires a secure connection (SSL). The incoming (POP3) port should be 110 and the outgoing (SMTP) port should be 587. To do this, right-click on the account name in the folder pane and select In case there is a problem with SSL, you could test the connection without it. (c) Which firewall do you have? Is it set to allow wlmail.exe and are the two ports open for POP3 and SMTP traffic? (b) Which anti-virus program are you using? Is it set to scan mail? If so, tell it not to mail scanning adds no real extra security and can cause problems. (a) AT&T won't admit this, but the error will eventually go away.
#ATT UVERSE MAIL SETTINGS SOFTWARE#
The commonest reasons are (a) temporary server outage, (b) interference from security software set to scan mail, and (c) incorrectly configured firewalls. Those error codes are notoriously difficult to troubleshoot.
0 kommentar(er)
